Raised-panel steel
Carriage house
Modern flush
Full-view glass
LiftMaster openers
Chamberlain openersFull 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the pro arrives.
Get your free estimateStyles & brands we work with
- Raised-panel steel
- Carriage house
- Modern flush
- Full-view glass
- LiftMaster openers
- Chamberlain openers
See the difference
Before
After
Before
After
Before
AfterHow Much Does Panel Replacement Cost in Arlington?
Panel replacement in Arlington typically costs $250 – $500 per section, including the new panel and labor. That estimate covers a standard residential panel on a sectional door; a full set of panels or a specialty or custom-order panel can land above that lead range. The written estimate you get after we look at the door is the price that applies.
Arlington’s housing stock makes this a common job. Between the brick colonials and older capes around Ashton Heights and the newer townhomes closer to Ballston, doors see a lot of daily use in tight driveways and alleys. One hard bump from a car, one dent from a runaway basketball, or a panel that’s taken on water along a bottom seam, and the rest of the door is still sound. Replacing the damaged section beats a full door replacement in most of those cases, and it costs a fraction of the $700 – $2,200 a whole new door runs. Our technicians have up to 12 years of experience, and we work on Clopay, Amarr, Wayne Dalton, and Raynor doors every day, so matching a panel profile and color is routine.
Call (855) 340-9110 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Key Takeaways
- A single damaged panel usually runs $250 – $500 in Arlington, parts and labor included.
- Panel replacement is the right call when the door still runs well and only the face is damaged.
- Dents, creases, cracked skins, rot along a bottom edge, and faded or mismatch colors are the most common reasons a panel gets swapped.
- If the door won’t move or the springs are broken, stop using the door and call before anything else gets done. Garage doors are heavy, and broken springs and cables are hazardous to work on.
- We handle panel replacement as a standalone job and can fold it into a larger repair if the opener or springs need attention too.
Panel Replacement Cost Breakdown (2026)
These are typical estimated ranges for the Arlington market. What you actually pay depends on the panel size, material, and whether the panel is a stock profile or a custom order. Our written estimate sets the final price.
| Job | Typical Estimated Range |
|---|---|
| Single panel replacement (stock profile) | $250 – $500 |
| Single panel, custom or specialty profile | At the top of the $250 – $500 range and above, per estimate |
| Garage door repair (general) | $150 – $600 |
| Track realignment | $120 – $240 |
| Roller replacement | $110 – $220 |
| Cable repair | $130 – $250 |
| Spring repair (one spring) | $180 – $340 |
| Opener repair | $120 – $320 |
| Opener installation | $250 – $550 |
| New door installation | $700 – $2,200 |
The panel itself is only part of the bill. Labor, safe removal of the old section, and color matching move the number. A standard steel panel in a common profile comes in lower than a custom-ordered panel that has to be matched to a discontinued line. A door that was installed years ago with a manufacturer that has since changed its panel colors can push the job toward the top of the range, because the panel has to be ordered and the color specially matched. Doors with windows or decorative inserts cost more per panel because the insert has to be reused or replaced along with the section.
The other thing that drives cost is what we find when we get there. A bent panel often comes with a bent track or a hinge that gave out at the same moment. If the door was hit by a car, the bottom section, the bottom bracket, and at least one roller usually need attention together. We’ll tell you on the estimate what’s part of the panel job and what’s separate, so nothing unexpected shows up later.
What Affects Panel Replacement Pricing in Arlington
- Panel profile and material. A standard raised-panel steel section in a common color is the cheapest to replace. A carriage-house style, a long-panel design, or a wood or wood-look door with a custom finish takes more time and, often, a special order.
- Color match. Sun fading changes steel panel color over time, even on a well-kept door. We compare the new panel to the existing sections in person and, where needed, order the closest match the manufacturer still produces. A perfect match is not always possible or affordable on an older discontinued color.
- Number of panels. One damaged section is the typical scenario. Several damaged panels, or a full face replacement, prices per panel and moves well above the single-panel range.
- Windows and inserts. Panels with decorative windows or inserts cost more because the glass or insert either carries over or gets replaced with the section, and the framing has to line up.
- Collateral damage. A panel that was hit or crushed usually brings a bent track, a tweaked hinge, or a stripped bottom bracket with it. Those are quoted as separate line items.
- Door type and access. A standard sectional door in a driveway is straightforward. A door in a tight alley or a low-clearance garage takes more setup time, which shows up in the labor line.
How to Save on Panel Replacement
Panel replacement is one of the few garage door jobs where saving money and keeping the door safe point in the same direction. A few things that help:
- Act before the damage spreads. A creased panel flexes every time the door runs. Left long enough, that flexing wears the hinge and the roller on that section, and you end up paying for two repairs instead of one.
- Repair the panel, not the door. If the operator, springs, and tracks are in good shape, a panel replacement is far cheaper than a new door. We’ll tell you honestly if the rest of the door is close to the end of its life and replacement makes more sense.
- Handle the small stuff at the same time. If a roller or hinge on the damaged section is worn, having it replaced during the panel job costs less than a separate visit later.
- Ask about a stock color. Staying with a standard manufacturer color usually costs less than a custom match.
- Get a written estimate before any work starts. Call (855) 340-9110 and we’ll walk you through the panel options for your door and put the price in writing.
We also handle opener repair, spring repair, and cable work, so if the door has more than one problem, one call covers all of it. If you’re not sure whether it’s a panel or something bigger, the main Garage Door Repair Arlington Pros page lays out the full range of what we do.
Is It Cheaper to Repair a Panel or Replace the Whole Door?
Replacing a panel is almost always cheaper than replacing the whole door. A single-panel replacement runs $250 – $500, while a new door installation runs $700 – $2,200. The one case where a full replacement wins is when the door is at the end of its usable life anyway. If three or four panels are damaged, the tracks are worn, and the hardware is original, putting in a new door can cost less than chasing damage one section at a time.
The honest answer usually comes down to two questions: how much of the door is actually damaged, and how old is the rest of it. If the door still runs smoothly and only one or two sections are hurt, replacement of the damaged panels is the sensible call. If the door shudders, the springs are tired, or the panels haven’t been made in years, we’ll say so, and a full door replacement goes on the table alongside the panel option. Call (855) 340-9110 for a straight answer on your door. Estimates are free.
Does Panel Replacement Cost More Than a Full Door Replacement in Arlington?
No. Panel replacement is much less than a full door replacement. A single panel typically runs $250 – $500 in Arlington, compared with $700 – $2,200 for a new door installed. The gap is even wider once you factor in that a new door often comes with new tracks, springs, and opener adjustments that a panel swap doesn’t touch.
The one thing that can close the gap is a rare, discontinued, or custom panel color that has to be specially matched. Even then, the job usually stays well below the cost of a new door. We’ll compare both options for your specific door and you can decide with the numbers in front of you. Call (855) 340-9110 and we’ll put together a free estimate.
Can You Replace Just One Panel on a Garage Door?
Yes. We replace single panels all the time. One dented or cracked section can be swapped out while the rest of the door stays in place. The new panel is matched to the existing door by profile, color, and panel height, and it’s reinstalled on the same tracks. Most single-panel jobs are done in one visit.
The catch is the match. Older doors and discontinued colors can be hard to match exactly, and we’ll tell you upfront what’s realistic. If the door has decorative inserts or windows in that section, the inserts are reused or replaced so the rebuilt section lines up with the original. Whether it’s one panel or a few, call (855) 340-9110 and we’ll tell you which sections need replacing and what it costs.
How Long Does Panel Replacement Take?
A single-panel replacement typically takes one to two hours, start to finish. A job that includes a second panel, a track adjustment, or new hinges and rollers runs longer, usually two to three hours. Custom-ordered panels add lead time before the job, because the panel has to be built and shipped before we can install it.
Most of the visit is careful, deliberate work: we check the rest of the door for hidden damage, confirm the new panel matches, fit the section, and test the door through several full cycles to make sure it’s balanced and running clean. It’s not a job to rush, because a panel that’s fitted wrong puts strain on the springs and the opener. To schedule a panel replacement, call (855) 340-9110. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Why Choose Garage Door Repair Arlington Pros for Panel Replacement?
Panel replacement is a fitting job. It only turns out well if the new panel matches the original in profile, color, and height, and if the rest of the door is checked for the damage that usually comes along with it. That’s where a specialist matters. We work on Clopay, Amarr, Wayne Dalton, and Raynor doors every day, and we’re familiar with the most widely installed garage door and opener brands, including LiftMaster, Chamberlain, Genie, and Craftsman. Our technicians have up to 12 years of experience.
We handle the full arc of garage door work under one roof: general repair, opener repair, spring repair, panel replacement, and full new installation. If a panel job turns up a bigger issue, we don’t send you to a second company. One call covers it. And when a door is stuck open or stuck closed and can’t wait, we offer dedicated emergency garage door service because a door that won’t run can’t sit until next week. For work outside our dispatch hours, call and we’ll book it into the next opening, Sunday through Friday, 7am to 7pm.
Call (855) 340-9110 for a free estimate. We’re glad to look at the door, tell you which panels need to go, and give you the price in writing before anything gets ordered.
FAQs – Panel Replacement Cost
How much does garage door panel replacement cost in Arlington in 2026?
Panel replacement in Arlington typically costs $250 – $500 per panel, parts and labor included. That covers a standard residential panel in a common profile. Custom or specialty panels price higher, and multiple panels price per section. Call (855) 340-9110 for an exact quote on your door. Estimates are free.
Will the new panel match the rest of my door?
In most cases, yes. We compare the new panel to the existing sections and order the closest match the manufacturer makes. On older doors with discontinued colors, an exact match may not be available, and we’ll tell you before you commit. Call (855) 340-9110 and we’ll walk you through the options for your specific door.
Can I replace a panel myself?
No, and we don’t recommend it. Garage doors are heavy, the springs are under high tension, and a mis-fitted panel can throw the door out of balance and strain the opener. Broken springs and cables are hazardous to work on. This is a job for a trained technician with the right tools. Call (855) 340-9110 to get it handled safely.
What causes a panel to need replacement?
The usual causes are a car hitting the door, a dent or crease from a ball or a bicycle, a crack in the panel skin, rot along a bottom edge, or fading and color mismatch that a homeowner wants fixed. In each case the rest of the door is usually fine, and swapping the damaged section costs far less than a new door. Call (855) 340-9110 and we’ll tell you if the panel can be repaired or needs replacing.
Are estimates free?
Yes. Estimates on panel replacement and all our other work are free. We look at the door, tell you what needs to happen, and give you the price in writing before any work starts. Call (855) 340-9110. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Pricing reflects the Arlington market as of 2026. Garage Door Repair Arlington Pros offers free estimates – call (855) 340-9110.
Written by the team at Garage Door Repair Arlington Pros.
What Our Customers Say
"Track was bent and two of the rollers were shot. He straightened what he could, swapped the rollers for nylon ones, lubricated everything, and had it done in about an hour."
- Kevin Mercer"Door installed in about four hours, old one hauled away, and he stayed to program both cars and the wall panel before he left."
- Dev Shah"Opener kept reversing halfway down. Turned out to be the safety sensors knocked out of alignment by a bicycle. He straightened them, wouldn't charge me for it, and just asked me to keep them in mind if I need real work later."
- Dale Doyle